Will the same product from two different manufacturers perform the same if they are marked the same?

This is a hard question to answer in a short space.  While the markings mean the wheels should perform the same, differences in factory equipment and marking systems may make one product behave differently than another.  They should be close, but the only true way to match a product is to have a wheel analysis done by the factory.  We do this for no charge and it is recommended for larger purchases to eliminate testing.  Note that even when an analysis is done, it is no guarantee the wheels will perform exactly the same.

More Questions

What is grit size?

Grit size typically runs from coarse (16 -24 grit), medium (36 – 60 grit) and fine (80-120 grit).  Superfine grits run from 150 and higher.  Grinding wheels usually will be between 24 and 100 grit.  Honing stones and

Coarseness of the abrasive mineral:

Commonly referred to as “grit”, this number designation is determined by the amount of abrasive mineral that can pass through a mesh screen with specific size openings. Therefore, a 40 grit abrasive particle will pass through a mesh

What is the specific weight?

The specific weight is the ratio of the weight of a body to its volume. The specific weight of corundum under normal conditions is 3.94 g/cm3.

What is the best way to store my abrasives?

The best way to have abrasive products retain maximum performance and work life is to store them properly. The bonding and backing materials used in abrasives are very sensitive to changes in temperature and humidity. Abrasives are best

What is the shelf life of fused aluminum oxide?

fused aluminum oxide products do not have a known shelf life. As long as the product is maintained in the original sealed container and stored in a cool, dry, ventilated area, our product will last indefinitely

What is the specific surface?

The specific surface means the outer surface of a substance including all accessible pores in relation to the mass. It is determined using the Brunauer-Emmett-Teller (BET) method.

What is the hardness?

Hardness is rated from A-Z with ‘A’ being the weakest bond and ‘Z’ being the strongest.  A weak bond is preferred for grinding harder materials while  a stronger bond is desired for softer materials.  A typical weak bond

What is silicon carbide?

Silicon carbide is a chemical compound of silicon and carbon and belongs to the group of carbides. The chemical formula is SiC.Silicon carbide is at the same time the hardest and lightest ceramic material and is also highly

What is mohs hardness?

Mohs hardness (according to Friedrich Mohs, 1773 – 1839) ascribes a relative hardness value to certain known minerals on a scale ranging from 1 (talc) to 10 (diamond). Accordingly, a mineral is considered harder than another if it

What is the warranty policy?

Firstly, We make sure the quality before the goods to be packed, if clients get the item with Substandard products, We have warranty for our clients,we will ship out the new replacements.

What does the term “flow properties” mean?

The flow behaviour of powders depends on many factors. The following applies in general: Coarser, dry grain types flow easily, but the fine the grains get, the stronger is the impact of morphology and various adhesive forces on

What is a silane coating used for?

When functionalising fused alumina, a very thin layer of a silane adsorption group is applied to the fused alumina particles. This organic surface coating has the effect of better embedding and increased scratch resistance in a melamine resin

Are you a manufacturer or trader ?

Yeah, We are the manufacturer of BFA, WFA, GC. Also,we had good business relationship with others abrasive media & refractory raw materials manufacturer . more over we have QC department which make strict inspection on goods quality, packing,

What is fepa and what does it do?

FEPA is the Federation of European Producers of Abrasives. Its mission is to develop and publish standards, documents and comprehensive safety instructions for the abrasive industry. Abrasive grain sizes are produced and sold according to the FEPA standard,

What is porosity?

Porosity is defined as the gas proportion (cavity volume) of a particle’s total volume. It can be determined using different measurement techniques, such as gas adsorption and mercury porosimetry. With the same grain size and shape, a lower

Product Category
Product News
Product Knowledge

The Smelting Furnace Of Brown Fused Aluminum Oxide-TAOANG

Over the past 18 years, TAOANG products range from raw material bauxite to processing follow-up products brown fused alumina, finishing white fused alumina and dense fused alumina, bubble alumina, and fused alumina micro powder. The production process is

Industry News

The Logicality Of Raw Material Price Rising

Fused Alumina is the tooth of industry and is widely used in various industries. TAOANG is committed to sharing information on the upstream and downstream industries of fused alumina. Raw material supply and market price performance are once

Brown Fused Aluminum Oxide Production In Feb

Fused Alumina is the tooth of industry and is widely used in various industries. TAOANG is committed to sharing information on the upstream and downstream industries of fused alumina. Brown fused Aluminum Oxide/aluminum oxide/ fused Fused Alumina market has

Company News

Taoang Industry – EQUALITY HARMONY PROGRESS

‘TAOANG’ means ‘Make Waves’ in Chinese, while ‘Promote the truth’ in Taoism. Henan Taoang Industrial was established and developed by the Yellow River, making waves in the industry and promoting the truth in business. TAOANG CORE VALUES: EQUALITY,

How is fused alumina obtained?

Raw materials containing aluminium oxide are electrothermally melted at a reaction temperature of more than 2,000 °C to produce the various fused aluminas. Different starting materials are used depending on the desired type of fused alumina. For instance,