What does the bulk weight indicate and what impacts the bulk weight?

According to the FEPA, the bulk density of an abrasive is the quotient of the mass and the volume a grain type poured out in a particular manner will occupy. The bulk density, also called bulk weight, is stated in g/cm3.

The rounder the particles, the higher the packing density, meaning the smaller the volume/grain size, the higher the bulk density.

More Questions

What is your terms of payment?

T/T 30% as deposit, and 70% before delivery. We’ll show you the photos of the products and packages .before you pay the balance.

What is porosity?

Porosity is defined as the gas proportion (cavity volume) of a particle’s total volume. It can be determined using different measurement techniques, such as gas adsorption and mercury porosimetry. With the same grain size and shape, a lower

What is the d50 value?

The d50 indicates the mean particle size. d50 means that 50% of particles fall within the specified grain size.

Form and shape of the abrasive:

This decision is made by determining how the abrasive will be used by the individual. Abrasives are sold in forms such as sheets, large/small discs, belts, and large/small rolls. Selecting the right form is determined by whether the

How is fused alumina obtained?

Raw materials containing aluminium oxide are electrothermally melted at a reaction temperature of more than 2,000 °C to produce the various fused aluminas. Different starting materials are used depending on the desired type of fused alumina. For instance,

What does the term “flow properties” mean?

The flow behaviour of powders depends on many factors. The following applies in general: Coarser, dry grain types flow easily, but the fine the grains get, the stronger is the impact of morphology and various adhesive forces on

Is sample parts testing available?

MicroBlasting is extremely efficient and precise, so it is hardly likely you will need to recycle abrasive, but it is important to know the risk involved. Unlike grit or bead blasting, a MicroBlasting system can only cycle abrasive

What is your sample policy?

We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and the courier cost. 

Can i get sample in free , how long is the time?

Yes, certainly. We will provide the sample is in free below 5 kgs for free, and the freight cost for free in 1kg. We could arrange the existing samples express delivery immediately. For any special samples requirement, it

What is the specification?

A typical grinding wheel specification consists of the grit type, the grit size, the hardness, the structure and the bond.  A typical grinding wheel specification would be A60-I10-VS.  ‘A’ is the grit type (aluminum oxide), ’60’ is the

How is silicon carbide obtained?

Silicon carbide (SiC) is produced from coke and quartz sand applying the Acheson process in an electric resistance furnace. When petrol coke and quartz sand are grouped around a graphite electrode and heated to a temperature of 2,000°C,

What is corundum?

Corundum is a mineral from the category of oxides and hydroxides and is the most frequently used industrial mineral worldwide. It also occurs naturally as a gemstone (sapphire, emerald, ruby). Chemically corundum is aluminium oxide with the chemical

What is melting vs. Sintering?

When processing minerals in a furnace, materials can either be melted or sintered.  When materials are melted during the production process the minerals go from a solid state, to a liquid state, then is re-solidified during the cooling process

What is the structure?

Structure is basically the spacing between abrasive grains.  An open structure would be 12 or higher while a closer structure would be 6 or so.  Here again, the structure depends on a variety of factors not the least

Product Category
Product News
Product Knowledge

Black Silicon Carbide Black Carborundum-TAOANG

Over the past 18 years, TAOANG products range from raw material bauxite to processing follow-up products brown fused alumina, finishing white fused alumina and dense fused alumina, bubble alumina, and fused alumina micro powder. The production process is

Acid Washed Brown Fused Aluminum Oxide-TAOANG

Over the past 18 years, TAOANG products range from raw material bauxite to processing follow-up products brown fused alumina, finishing white fused alumina and dense fused alumina, bubble alumina, and fused alumina micro powder. The production process is

Aluminum Oxide – Brown-TAOANG

Over the past 18 years, TAOANG products range from raw material bauxite to processing follow-up products brown fused alumina, finishing white fused alumina and dense fused alumina, bubble alumina, and fused alumina micro powder. The production process is

Industry News

Land Freight Goes Up Due To Discriminative Truck Ban

Fused Alumina is the tooth of industry and is widely used in various industries. TAOANG is committed to sharing information on the upstream and downstream industries of fused alumina. The administrative bureau of Tianjin port has released a

What Are The Raw Materials For Smelting Ferrosilicon

Fused Alumina is the tooth of industry and is widely used in various industries. TAOANG is committed to sharing information on the upstream and downstream industries of fused alumina. Ferrosilicon is a combined iron alloy that is used

The Operation Rate Of Fused Alumina Plant In Yichuan

Fused Alumina is the tooth of industry and is widely used in various industries. TAOANG is committed to sharing information on the upstream and downstream industries of fused alumina. The Operation Rate of Fused Alumina Plant in Yichuan Affected

Company News

How is fused alumina obtained?

Raw materials containing aluminium oxide are electrothermally melted at a reaction temperature of more than 2,000 °C to produce the various fused aluminas. Different starting materials are used depending on the desired type of fused alumina. For instance,